M8 armoured car bits and pieces for sale
-
- G-Captain
- Posts: 788
- Joined: Sat Sep 19, 2009 11:22 pm
- Location:
M8 armoured car bits and pieces for sale
Hi all,
I am starting to accumulate a few parts spare from my ongoing M8 restoration which I'll list here. These parts are surplus to my restoration and may be of use to someone else. I’ve attached a photo and a brief description. Please PM me if you want additional details or photos and I’ll email them to you. I can work out the freight cost at the time. The spare 37mm gun parts I had are now all sold.
* 37mm ready rack - missing the holders for the projectile end of the 37mm round. Asking $40 US ( sold)
* Instrument panel face plate - there is some corrosion around the speedo area which will need tidying up and filling. Asking $30 USD.
* Handbrake adjusting pin- this is a little bent but should straighten fine. Asking $5 USD.
* Transmission lever housing - some areas around the base have been damaged by corrosion. Asking $40 USD.
* Light Switch - I have checked this with a multimeter and it appears to work correctly. The indicator plate has been painted over but it is restorable. Asking $20.
* Turret traverse housing - a part of this where the handle would be has been cut away. Asking $5.
I am starting to accumulate a few parts spare from my ongoing M8 restoration which I'll list here. These parts are surplus to my restoration and may be of use to someone else. I’ve attached a photo and a brief description. Please PM me if you want additional details or photos and I’ll email them to you. I can work out the freight cost at the time. The spare 37mm gun parts I had are now all sold.
* 37mm ready rack - missing the holders for the projectile end of the 37mm round. Asking $40 US ( sold)
* Instrument panel face plate - there is some corrosion around the speedo area which will need tidying up and filling. Asking $30 USD.
* Handbrake adjusting pin- this is a little bent but should straighten fine. Asking $5 USD.
* Transmission lever housing - some areas around the base have been damaged by corrosion. Asking $40 USD.
* Light Switch - I have checked this with a multimeter and it appears to work correctly. The indicator plate has been painted over but it is restorable. Asking $20.
* Turret traverse housing - a part of this where the handle would be has been cut away. Asking $5.
- Attachments
-
- IMG_0973.JPG (128.98 KiB) Viewed 4932 times
-
- IMG_0974.JPG (149.2 KiB) Viewed 4932 times
-
- IMG_0774.JPG (190.99 KiB) Viewed 4932 times
-
- IMG_0865.JPG (143.32 KiB) Viewed 4932 times
-
- IMG_0777.JPG (143.09 KiB) Viewed 4932 times
-
- IMG_0778.JPG (145.43 KiB) Viewed 4932 times
Last edited by Big D on Thu Mar 10, 2016 1:01 pm, edited 2 times in total.
Darryl Lennane
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
-
- G-First Lieutenant
- Posts: 640
- Joined: Thu Dec 30, 2004 6:45 pm
- Location:
Re: M8 armoured car bits and pieces for sale
PM sent.
Thanks,
Dave
Thanks,
Dave
-
- G-Captain
- Posts: 788
- Joined: Sat Sep 19, 2009 11:22 pm
- Location:
Re: M8 armoured car bits and pieces for sale
Here are some more items that I have surplus:
Turret hold down roller assemblies:
* 5 x housings in good condition with horizontal roller and pin. No vertical roller or pin. Asking $40 USD each (sold)
* 1 x housing in good condition. No rollers or pins - $15 USD (sold)
* 1 x housing with damage to vertical roller pin mount area. No rollers or pins - $5 USD (sold)
.30 cal MG mount.
Tidied up and primed and in good condition. Asking $60 USD
Turret hold down roller assemblies:
* 5 x housings in good condition with horizontal roller and pin. No vertical roller or pin. Asking $40 USD each (sold)
* 1 x housing in good condition. No rollers or pins - $15 USD (sold)
* 1 x housing with damage to vertical roller pin mount area. No rollers or pins - $5 USD (sold)
.30 cal MG mount.
Tidied up and primed and in good condition. Asking $60 USD
- Attachments
-
- IMG_1184.JPG (166.54 KiB) Viewed 4844 times
-
- IMG_1183.JPG (216.59 KiB) Viewed 4844 times
Last edited by Big D on Tue Jun 21, 2016 6:50 pm, edited 2 times in total.
Darryl Lennane
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
-
- G-Corporal
- Posts: 18
- Joined: Wed Sep 02, 2009 2:51 pm
- Location:
Re: M8 armoured car bits and pieces for sale
PM sent
Thanks
Thanks
-
- G-Captain
- Posts: 788
- Joined: Sat Sep 19, 2009 11:22 pm
- Location:
Re: M8 armoured car bits and pieces for sale
Hi all
Bumped to the top with new prices on what is left:
* .30 cal MG mount - tidied up and primed and in good condition. Asking $40 USD
(sold)
* Turret hold down roller assemblies - 1 x housing in good condition. No rollers or pins - $10 USD; 1 x housing with damage to vertical roller pin mount area. No rollers or pins - $5 USD (sold)
* Instrument panel face plate - there is some corrosion around the speedo area which will need tidying up and filling. Asking $20 USD.
* Handbrake adjusting pin- this is a little bent but should straighten fine. Asking $5 USD.
* Transmission lever housing - some areas around the base have been damaged by corrosion. Asking $30 USD.
* Light Switch - I have checked this with a multimeter and it appears to work correctly. The indicator plate has been painted over but it is restorable. Asking $15.
* Turret traverse housing - a part of this where the handle would be has been cut away. Asking $5.
PM if interested please.
Bumped to the top with new prices on what is left:
* .30 cal MG mount - tidied up and primed and in good condition. Asking $40 USD
(sold)
* Turret hold down roller assemblies - 1 x housing in good condition. No rollers or pins - $10 USD; 1 x housing with damage to vertical roller pin mount area. No rollers or pins - $5 USD (sold)
* Instrument panel face plate - there is some corrosion around the speedo area which will need tidying up and filling. Asking $20 USD.
* Handbrake adjusting pin- this is a little bent but should straighten fine. Asking $5 USD.
* Transmission lever housing - some areas around the base have been damaged by corrosion. Asking $30 USD.
* Light Switch - I have checked this with a multimeter and it appears to work correctly. The indicator plate has been painted over but it is restorable. Asking $15.
* Turret traverse housing - a part of this where the handle would be has been cut away. Asking $5.
PM if interested please.
Last edited by Big D on Tue Jun 21, 2016 6:55 pm, edited 1 time in total.
Darryl Lennane
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
-
- G-Captain
- Posts: 788
- Joined: Sat Sep 19, 2009 11:22 pm
- Location:
Re: M8 armoured car bits and pieces for sale
Hi all,
I have these turret seats and tower mounts surplus now if anyone is looking for them.
Both towers will need to have some repair work on the base of the tower where corrosion has got to them.
The seats will need new rollers and some fabrication of the lock lever.
I'm asking $200 USD for both plus the ride there.
PM if interested please.
I have these turret seats and tower mounts surplus now if anyone is looking for them.
Both towers will need to have some repair work on the base of the tower where corrosion has got to them.
The seats will need new rollers and some fabrication of the lock lever.
I'm asking $200 USD for both plus the ride there.
PM if interested please.
- Attachments
-
- P1060917.JPG (210.14 KiB) Viewed 4538 times
Darryl Lennane
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
-
- G-Captain
- Posts: 788
- Joined: Sat Sep 19, 2009 11:22 pm
- Location:
Re: M8 armoured car bits and pieces for sale
Hi all,
Here are a few additional parts which are surplus to my restoration.
• Torque rod end – NOS - $25
• Brake backing plate – will require some straightening - $25
• Brake backing plate – appears in good condition - $50
• Brake parts – assorted - $30
• Axle grease seals - $4 each
• Distributor - $50. Complete with cap. No points or condenser.
• Gun trigger control cable end - $10. With grease nipple.
• Torque rod - $40
I also have a spare front hatch in good condition.
Please PM me for more details or photos and freight estimate.
Here are a few additional parts which are surplus to my restoration.
• Torque rod end – NOS - $25
• Brake backing plate – will require some straightening - $25
• Brake backing plate – appears in good condition - $50
• Brake parts – assorted - $30
• Axle grease seals - $4 each
• Distributor - $50. Complete with cap. No points or condenser.
• Gun trigger control cable end - $10. With grease nipple.
• Torque rod - $40
I also have a spare front hatch in good condition.
Please PM me for more details or photos and freight estimate.
- Attachments
-
- Torque rod end.jpg (73.61 KiB) Viewed 4359 times
-
- Brake backing plate.jpg (92.05 KiB) Viewed 4359 times
-
- Brake backing plate 2.jpg (91.65 KiB) Viewed 4359 times
-
- Brake parts.jpg (85.79 KiB) Viewed 4359 times
-
- Grease seal.jpg (110.25 KiB) Viewed 4359 times
-
- distributor.jpg (123.26 KiB) Viewed 4359 times
-
- gun cable end.jpg (121.63 KiB) Viewed 4359 times
-
- Torque rod.jpg (85.16 KiB) Viewed 4359 times
Darryl Lennane
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
-
- G-Captain
- Posts: 788
- Joined: Sat Sep 19, 2009 11:22 pm
- Location:
Re: M8 armoured car bits and pieces for sale
Hi all,
Here are a few other bits and pieces that are surplus:
* Protectoscope support pieces = $50 for the pair
* Gun mount part = $30
* Wiper motor = $40 (now sold)
* Hull rubber stoppers = $10 for all three (now sold)
Please PM if interested.
Here are a few other bits and pieces that are surplus:
* Protectoscope support pieces = $50 for the pair
* Gun mount part = $30
* Wiper motor = $40 (now sold)
* Hull rubber stoppers = $10 for all three (now sold)
Please PM if interested.
- Attachments
-
- IMG_0225.JPG (173.5 KiB) Viewed 4266 times
-
- Gun mount piece.jpg (128.8 KiB) Viewed 4266 times
-
- Wiper motor.jpg (101.74 KiB) Viewed 4266 times
-
- Wiper motor 2.jpg (114.78 KiB) Viewed 4266 times
-
- Rubber stoppers.jpg (120.77 KiB) Viewed 4266 times
Darryl Lennane
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
-
- G-Captain
- Posts: 788
- Joined: Sat Sep 19, 2009 11:22 pm
- Location:
Re: M8 armoured car bits and pieces for sale
Hi all,
Here is an update on parts I have which are surplus to my restoration:
* Turret seats and towers. They will require restoration. Asking $150 for the pair (Sold).
* Transmission lever housing – the top has been cutaway but is otherwise in very good shape. Complete with levers and locking screws. Asking $150 USD.
* Fan tunnels for the radiator. New reproduction. $120 USD each.
* Clutch master cylinder. Needs restoration. Asking $50 USD.
* Brake master cylinder. Appears rstorable. Asking $50 USD.
* Torque rod end. NOS. Asking $25 USD. (Sold)
* French headlights. Tidy condition but blackout lights need repairing. Asking $30 USD each.
* Brake backing plate. Will require some straightening. Asking $20 USD.
* Brake backing plate. Appears in good condition. Asking $40 USD.
* Brake shoe return springs. Good condition. Asking $25 USD each (Sold)
* Brake slave cylinder caps. Will require restoration. Asking $10 USD for the adjustable end and $5 USD for the fixed end.
* Brake slave cylinders. All require restoration. Several available. Can combine cups, caps and cylinders if required. Asking $50 USD each.
* Brake adjustment locking plate. Asking $5 USD.
* Brake shoe securing bolts with springs. Good condition. Asking $10 USD each.
* Sponson cover. French made. Rough but repairable. Asking $20 USD.
* Tool lockers. 2 x driver’s side and 1 x co-driver side. Pretty rough. I’d say one is repairable, the other two only good for a template or donor. Asking $50 USD each.
* Grenade box. Restored and painted. Latch pin is not original. Asking $50 USD.
* 37mm rack part. Asking $10 USD.
* Carbine clips for the seat towers. Unsure if they are M8 or not, but they are close. Asking $15 USD each. (Sold)
* Light Switch. Appears to work correctly. The indicator plate has been painted over but it is restorable. Asking $20.
* Transmission lever housing. Corrosion damage around the base. Asking $20 USD.
* Instrument panel face plate. Some corrosion around the speedo area which will need tidying up and filling. Asking $20 USD.
* Handbrake adjusting pin. A little bent but should straighten. Asking $5 USD.
* Turret traverse housing piece. A part of this where the handle would be has been cut away. Asking $5.
* Propellor shaft piece. Requires repair. Asking $10 USD.
* Axle grease seals. Asking $4 USD each.
* Distributor. Complete with cap. No points or condenser. Asking $50 USD.
* Gun trigger control cable end, with grease nipple. Asking $15 USD. (Sold)
* Torque rod. Pin at one end needs straightening. Asking $40 USD (Sold)
* Driver hatch. Will need repairs to hinges. Very heavy. Asking $100 USD (Sold)
* Protectoscope box side pieces. Asking $30 USD for the pair. (Sold)
* Elevation gear adjuster/locking piece. Asking $15 USD. (Sold)
Please PM me for more details/photos and freight estimate, or if you wish to negotiate!
Here is an update on parts I have which are surplus to my restoration:
* Turret seats and towers. They will require restoration. Asking $150 for the pair (Sold).
* Transmission lever housing – the top has been cutaway but is otherwise in very good shape. Complete with levers and locking screws. Asking $150 USD.
* Fan tunnels for the radiator. New reproduction. $120 USD each.
* Clutch master cylinder. Needs restoration. Asking $50 USD.
* Brake master cylinder. Appears rstorable. Asking $50 USD.
* Torque rod end. NOS. Asking $25 USD. (Sold)
* French headlights. Tidy condition but blackout lights need repairing. Asking $30 USD each.
* Brake backing plate. Will require some straightening. Asking $20 USD.
* Brake backing plate. Appears in good condition. Asking $40 USD.
* Brake shoe return springs. Good condition. Asking $25 USD each (Sold)
* Brake slave cylinder caps. Will require restoration. Asking $10 USD for the adjustable end and $5 USD for the fixed end.
* Brake slave cylinders. All require restoration. Several available. Can combine cups, caps and cylinders if required. Asking $50 USD each.
* Brake adjustment locking plate. Asking $5 USD.
* Brake shoe securing bolts with springs. Good condition. Asking $10 USD each.
* Sponson cover. French made. Rough but repairable. Asking $20 USD.
* Tool lockers. 2 x driver’s side and 1 x co-driver side. Pretty rough. I’d say one is repairable, the other two only good for a template or donor. Asking $50 USD each.
* Grenade box. Restored and painted. Latch pin is not original. Asking $50 USD.
* 37mm rack part. Asking $10 USD.
* Carbine clips for the seat towers. Unsure if they are M8 or not, but they are close. Asking $15 USD each. (Sold)
* Light Switch. Appears to work correctly. The indicator plate has been painted over but it is restorable. Asking $20.
* Transmission lever housing. Corrosion damage around the base. Asking $20 USD.
* Instrument panel face plate. Some corrosion around the speedo area which will need tidying up and filling. Asking $20 USD.
* Handbrake adjusting pin. A little bent but should straighten. Asking $5 USD.
* Turret traverse housing piece. A part of this where the handle would be has been cut away. Asking $5.
* Propellor shaft piece. Requires repair. Asking $10 USD.
* Axle grease seals. Asking $4 USD each.
* Distributor. Complete with cap. No points or condenser. Asking $50 USD.
* Gun trigger control cable end, with grease nipple. Asking $15 USD. (Sold)
* Torque rod. Pin at one end needs straightening. Asking $40 USD (Sold)
* Driver hatch. Will need repairs to hinges. Very heavy. Asking $100 USD (Sold)
* Protectoscope box side pieces. Asking $30 USD for the pair. (Sold)
* Elevation gear adjuster/locking piece. Asking $15 USD. (Sold)
Please PM me for more details/photos and freight estimate, or if you wish to negotiate!
- Attachments
-
- Grenade box.jpg (28.87 KiB) Viewed 4091 times
-
- IMG_0713.JPG (189.5 KiB) Viewed 4091 times
-
- French headlights.jpg (24.03 KiB) Viewed 4091 times
-
- Driver hatch.jpg (22.53 KiB) Viewed 4091 times
-
- Clutch master cylinder.jpg (25.32 KiB) Viewed 4091 times
-
- Carbine clips.jpg (26.73 KiB) Viewed 4091 times
-
- Brake shoe return springs.jpg (23.33 KiB) Viewed 4091 times
-
- Brake shoe holding bolts and springs.jpg (25.47 KiB) Viewed 4091 times
-
- Brake adjuster locking plate.jpg (22.53 KiB) Viewed 4091 times
-
- 37mm rack part.jpg (22.51 KiB) Viewed 4091 times
Last edited by Big D on Sat Jan 28, 2017 1:22 pm, edited 4 times in total.
Darryl Lennane
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
-
- G-Captain
- Posts: 788
- Joined: Sat Sep 19, 2009 11:22 pm
- Location:
Re: M8 armoured car bits and pieces for sale
Some more photos....
- Attachments
-
- Transmission housing and levers.jpg (22.37 KiB) Viewed 4091 times
-
- Sponson covers 3.jpg (133.71 KiB) Viewed 4091 times
-
- Slave cylinders 1.jpg (32.25 KiB) Viewed 4091 times
-
- Slave cylinder caps.jpg (24.06 KiB) Viewed 4091 times
-
- Propellor shaft end.jpg (22.6 KiB) Viewed 4091 times
-
- Firing cable end.jpg (185.86 KiB) Viewed 4091 times
-
- Brake master cylinder.jpg (30.86 KiB) Viewed 4091 times
Darryl Lennane
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
-
- G-Captain
- Posts: 788
- Joined: Sat Sep 19, 2009 11:22 pm
- Location:
Re: M8 armoured car bits and pieces for sale
Updated with items just sold.
Darryl Lennane
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
-
- G-Captain
- Posts: 788
- Joined: Sat Sep 19, 2009 11:22 pm
- Location:
Re: M8 armoured car bits and pieces for sale
Updated with more items just sold.
Darryl Lennane
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
-
- G-Captain
- Posts: 788
- Joined: Sat Sep 19, 2009 11:22 pm
- Location:
Re: M8 armoured car bits and pieces for sale
Hi all,
I’ve added a couple more items which are now surplus. I’ve also listed what is left:
* Pintle hook assembly. Asking $100 USD. Heavy.
* Passenger seat. Good condition and primed. Missing the mounting base and spring etc. Asking $150 USD.
* Protectoscope box holders. Both are bent and will require a little heat and straightening. $5 USD each.
* Shock absorber mount. A little corroded and one of the mounting tabs is a little bent. Asking $10 USD.
* Transmission lever housing – the top has been cutaway but is otherwise in very good shape. Complete with levers and locking screws. Asking $150 USD.
* Fan tunnels for the radiator. New reproduction. $120 USD each.
* Clutch master cylinder. Needs restoration. Asking $50 USD.
* Brake master cylinder. Appears restorable. Asking $50 USD.
* French headlights. Tidy condition but blackout lights need repairing. Asking $30 USD each.
* Brake backing plate. Will require some straightening. Asking $20 USD.
* Brake backing plate. Appears in good condition. Asking $40 USD.
* Brake slave cylinder caps. Will require restoration. Asking $10 USD for the adjustable end and $5 USD for the fixed end.
* Brake slave cylinders. All require restoration. Several available. Can combine cups, caps and cylinders if required. Asking $50 USD each.
* Brake adjustment locking plate. Asking $5 USD.
* Brake shoe securing bolts with springs. Good condition. Asking $10 USD each.
* Sponson cover. French made. Rough but repairable. Asking $20 USD.
* Tool lockers. 2 x driver’s side and 1 x co-driver side. Pretty rough. I’d say one is repairable, the other two only good for a template or donor. Asking $50 USD each.
* Grenade box. Restored and painted. Latch pin is not original. Asking $50 USD.
* 37mm rack part. Asking $10 USD.
* Light Switch. Appears to work correctly. The indicator plate has been painted over but it is restorable. Asking $20.
* Transmission lever housing. Corrosion damage around the base. Asking $20 USD.
* Instrument panel face plate. Some corrosion around the speedo area which will need tidying up and filling. Asking $20 USD.
* Handbrake adjusting pin. A little bent but should straighten. Asking $5 USD.
* Turret traverse housing piece. A part of this where the handle would be has been cut away. Asking $5.
* Propellor shaft piece. Requires repair. Asking $10 USD.
* Axle grease seals. Asking $4 USD each.
* Distributor. Complete with cap. No points or condenser. Asking $50 USD.
Please PM me for more details/photos and freight estimate, or if you wish to negotiate!
I’ve added a couple more items which are now surplus. I’ve also listed what is left:
* Pintle hook assembly. Asking $100 USD. Heavy.
* Passenger seat. Good condition and primed. Missing the mounting base and spring etc. Asking $150 USD.
* Protectoscope box holders. Both are bent and will require a little heat and straightening. $5 USD each.
* Shock absorber mount. A little corroded and one of the mounting tabs is a little bent. Asking $10 USD.
* Transmission lever housing – the top has been cutaway but is otherwise in very good shape. Complete with levers and locking screws. Asking $150 USD.
* Fan tunnels for the radiator. New reproduction. $120 USD each.
* Clutch master cylinder. Needs restoration. Asking $50 USD.
* Brake master cylinder. Appears restorable. Asking $50 USD.
* French headlights. Tidy condition but blackout lights need repairing. Asking $30 USD each.
* Brake backing plate. Will require some straightening. Asking $20 USD.
* Brake backing plate. Appears in good condition. Asking $40 USD.
* Brake slave cylinder caps. Will require restoration. Asking $10 USD for the adjustable end and $5 USD for the fixed end.
* Brake slave cylinders. All require restoration. Several available. Can combine cups, caps and cylinders if required. Asking $50 USD each.
* Brake adjustment locking plate. Asking $5 USD.
* Brake shoe securing bolts with springs. Good condition. Asking $10 USD each.
* Sponson cover. French made. Rough but repairable. Asking $20 USD.
* Tool lockers. 2 x driver’s side and 1 x co-driver side. Pretty rough. I’d say one is repairable, the other two only good for a template or donor. Asking $50 USD each.
* Grenade box. Restored and painted. Latch pin is not original. Asking $50 USD.
* 37mm rack part. Asking $10 USD.
* Light Switch. Appears to work correctly. The indicator plate has been painted over but it is restorable. Asking $20.
* Transmission lever housing. Corrosion damage around the base. Asking $20 USD.
* Instrument panel face plate. Some corrosion around the speedo area which will need tidying up and filling. Asking $20 USD.
* Handbrake adjusting pin. A little bent but should straighten. Asking $5 USD.
* Turret traverse housing piece. A part of this where the handle would be has been cut away. Asking $5.
* Propellor shaft piece. Requires repair. Asking $10 USD.
* Axle grease seals. Asking $4 USD each.
* Distributor. Complete with cap. No points or condenser. Asking $50 USD.
Please PM me for more details/photos and freight estimate, or if you wish to negotiate!
- Attachments
-
- Shock absorber mount.jpg (144.02 KiB) Viewed 3878 times
-
- Protectoscope box holders.jpg (103.44 KiB) Viewed 3878 times
-
- IMG_0692 - Copy.JPG (248.85 KiB) Viewed 3878 times
Darryl Lennane
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
-
- G-Captain
- Posts: 788
- Joined: Sat Sep 19, 2009 11:22 pm
- Location:
Re: M8 armoured car bits and pieces for sale
Hi all,
I’ve added a couple more items which are now surplus to my M8 restoration. I’ve also listed what is left:
* Exhaust piece. One end missing but still has the heat shield. Asking $30 USD.
* Drag link. NOS. Asking $120 USD.
* Turret traverse knob. Asking $10 USD.
* BC606 intercom box. Appears to be in reasonable condition. Asking $15 USD (sold)
* Pintle hook assembly. Asking $100 USD. Heavy(sold)
* Protectoscope box holders. Both are bent and will require a little heat and straightening. $5 USD each (sold)
* Shock absorber mount. A little corroded and one of the mounting tabs is a little bent. Asking $10 USD.
* Transmission lever housing – the top has been cutaway but is otherwise in very good shape. Complete with levers and locking screws. Asking $150 USD.
* Fan tunnels for the radiator. New reproduction. $120 USD each.
* French headlights. Tidy condition but blackout lights need repairing. Asking $30 USD each(sold) .
* Brake backing plate. Will require some straightening. Asking $20 USD.
* Brake backing plate. Appears in good condition. Asking $40 USD.
* Brake slave cylinder caps. Will require restoration. Asking $10 USD for the adjustable end and $5 USD for the fixed end.
* Brake slave cylinders. All require restoration. Several available. Can combine cups, caps and cylinders if required. Asking $50 USD each (sold)
* Brake adjustment locking plate. Asking $5 USD.
* Brake shoe securing bolts with springs. Good condition. Asking $10 USD each.
* Sponson cover. French made. Rough but repairable. Asking $20 USD.
* Grenade box. Restored and painted. Latch pin is not original. Asking $50 USD.
* 37mm rack part. Asking $10 USD.
* Light Switch. Appears to work correctly. The indicator plate has been painted over but it is restorable. Asking $20(sold).
* Transmission lever housing. Corrosion damage around the base. Asking $20 USD.
* Instrument panel face plate. Some corrosion around the speedo area which will need tidying up and filling. Asking $20 USD (sold).
* Handbrake adjusting pin. A little bent but should straighten. Asking $5 USD.
* Turret traverse housing piece. A part of this where the handle would be has been cut away. Asking $5.
* Propellor shaft piece. Requires repair. Asking $10 USD.
* Axle grease seals. Asking $4 USD each.
* Distributor. Complete with cap. No points or condenser. Asking $50 USD.
Please PM me for more details/photos and freight estimate, or if you wish to negotiate!
I’ve added a couple more items which are now surplus to my M8 restoration. I’ve also listed what is left:
* Exhaust piece. One end missing but still has the heat shield. Asking $30 USD.
* Drag link. NOS. Asking $120 USD.
* Turret traverse knob. Asking $10 USD.
* BC606 intercom box. Appears to be in reasonable condition. Asking $15 USD (sold)
* Pintle hook assembly. Asking $100 USD. Heavy(sold)
* Protectoscope box holders. Both are bent and will require a little heat and straightening. $5 USD each (sold)
* Shock absorber mount. A little corroded and one of the mounting tabs is a little bent. Asking $10 USD.
* Transmission lever housing – the top has been cutaway but is otherwise in very good shape. Complete with levers and locking screws. Asking $150 USD.
* Fan tunnels for the radiator. New reproduction. $120 USD each.
* French headlights. Tidy condition but blackout lights need repairing. Asking $30 USD each(sold) .
* Brake backing plate. Will require some straightening. Asking $20 USD.
* Brake backing plate. Appears in good condition. Asking $40 USD.
* Brake slave cylinder caps. Will require restoration. Asking $10 USD for the adjustable end and $5 USD for the fixed end.
* Brake slave cylinders. All require restoration. Several available. Can combine cups, caps and cylinders if required. Asking $50 USD each (sold)
* Brake adjustment locking plate. Asking $5 USD.
* Brake shoe securing bolts with springs. Good condition. Asking $10 USD each.
* Sponson cover. French made. Rough but repairable. Asking $20 USD.
* Grenade box. Restored and painted. Latch pin is not original. Asking $50 USD.
* 37mm rack part. Asking $10 USD.
* Light Switch. Appears to work correctly. The indicator plate has been painted over but it is restorable. Asking $20(sold).
* Transmission lever housing. Corrosion damage around the base. Asking $20 USD.
* Instrument panel face plate. Some corrosion around the speedo area which will need tidying up and filling. Asking $20 USD (sold).
* Handbrake adjusting pin. A little bent but should straighten. Asking $5 USD.
* Turret traverse housing piece. A part of this where the handle would be has been cut away. Asking $5.
* Propellor shaft piece. Requires repair. Asking $10 USD.
* Axle grease seals. Asking $4 USD each.
* Distributor. Complete with cap. No points or condenser. Asking $50 USD.
Please PM me for more details/photos and freight estimate, or if you wish to negotiate!
- Attachments
-
- IMG_1144.JPG (202.54 KiB) Viewed 3731 times
-
- IMG_1189.JPG (206.18 KiB) Viewed 3731 times
-
- IMG_1149.JPG (233.28 KiB) Viewed 3731 times
-
- IMG_1191.JPG (230.93 KiB) Viewed 3731 times
-
- IMG_1185.JPG (219.9 KiB) Viewed 3731 times
Last edited by Big D on Fri Sep 01, 2017 12:45 am, edited 5 times in total.
Darryl Lennane
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
NZ
1943 Willys MB
1941 LP2A MG Carrier
1943 White M3A1 AOP
1942 Willys MBT
1944 Ford M8 Armoured Car
1945 Ford M20 Armoured Car
-
- G-First Sergeant
- Posts: 142
- Joined: Wed Mar 23, 2016 8:12 pm
- Location:
Re: M8 armoured car bits and pieces for sale
any m6 gun mount sleighs, or where you got yours? thanks
Who is online
Users browsing this forum: No registered users and 54 guests