How to mount jerrycan on side step?
-
- G-Captain
- Posts: 704
- Joined: Thu Jul 19, 2007 10:32 am
- Location: Corinth, MS 38834
- Contact:
How to mount jerrycan on side step?
Do you normally use a jerry can holder to do this or just set the can on the step? If no holder what type of strap?
Thanks
Thanks
45 Willys MB, MBT, Harley WLA
- USAFpj
- G-Brigadier General
- Posts: 2217
- Joined: Sun Aug 08, 2004 1:02 pm
- Location: SC
Re: How to mount jerrycan on side step?
What I've seen, is that if you're using a full can, a holder is placed on the outside, but then a piece of metal 'backing" is on the inside of the jeep to keep the sheet metal from warping over time.
-
- G-Captain
- Posts: 704
- Joined: Thu Jul 19, 2007 10:32 am
- Location: Corinth, MS 38834
- Contact:
Re: How to mount jerrycan on side step?
I sat mine on the step today w/out the holder and it hit the windshield arm??
45 Willys MB, MBT, Harley WLA
- gerrykan
- G-General
- Posts: 9303
- Joined: Fri Apr 07, 2006 3:37 am
- Location: Ozark Mountains, USA
Re: How to mount jerrycan on side step?
pvtcook,
Derek Eddlestone has one mounted on his jeep. He spoke of it having a "stand off plate"(if my memory is correct) to prevent the can from interfering with the windshield arm.
There was a stand off plate/spacer used on halftracks between the jerrycan holder and cowl that may also work.
If you study period photographs, there were a lot of field modifications that used whatever material was available.
The following photo is a step mounted can on a USMC jeep that(by photographic evidence) seems to have been a common addition for the Corps, but there were also a lot of US Army jeeps with similar brackets.
Derek Eddlestone has one mounted on his jeep. He spoke of it having a "stand off plate"(if my memory is correct) to prevent the can from interfering with the windshield arm.
There was a stand off plate/spacer used on halftracks between the jerrycan holder and cowl that may also work.
If you study period photographs, there were a lot of field modifications that used whatever material was available.
The following photo is a step mounted can on a USMC jeep that(by photographic evidence) seems to have been a common addition for the Corps, but there were also a lot of US Army jeeps with similar brackets.
Roy
- lucakiki
- G-General
- Posts: 17578
- Joined: Sat Feb 15, 2003 7:18 am
- Location: Torino, ITALY
One way to mount jerrycan on side step.
Derek Eddlestone wrote:My bracket came from one of the surplus dealers who brought a lot of vehicles back from Greece. I can't say I've cleaned it back to bare metal in search of a number but if someone was making them, they made a lot. My jeep had the holes already drilled in it to accept the bracket but at some point they had been welded up........ not very carefully, so they were easy to find and re-drill.
The bracket is made of 3/16" plate.
The widest part onto which the J/Can bracket bolts is 8" in width.
From the widest part it steps back at 90 degrees towards the jeep for 1+1/2" on both the left and the right side.
There is then another 90 degree bend in the opposite direction for a further 1+1/2". This second 'flat' has two holes drilled (total of 4) with 3+1/2" centres, equally spaced between the upper and lower edges of the bracket.
The bracket is 5+5/8" in depth.
The holes are sized to take 9/16" AF bolts.
Luca
WillysMB#344142 6-19-44 Navy N.S.Blue Grey
45 Bantam T-3 #57248 1-10-45
42 Willys MB-T #13560 11-42
43 Willys MB-T # 25417 4-43
Way too many WWII military tools,hopefully thinning down,and way too many posts...
__________________________________________
_____________________________________________
__________________________________________
WillysMB#344142 6-19-44 Navy N.S.Blue Grey
45 Bantam T-3 #57248 1-10-45
42 Willys MB-T #13560 11-42
43 Willys MB-T # 25417 4-43
Way too many WWII military tools,hopefully thinning down,and way too many posts...
__________________________________________
_____________________________________________
__________________________________________
-
- G-Captain
- Posts: 704
- Joined: Thu Jul 19, 2007 10:32 am
- Location: Corinth, MS 38834
- Contact:
Re: How to mount jerrycan on side step?
I appreciate it man. I think I can fabricate that. Thanks alot.
45 Willys MB, MBT, Harley WLA
- Chuck Lutz
- Gee Addict
- Posts: 26829
- Joined: Wed Jun 28, 2006 7:00 am
- Location: Jeep Heaven
Re: How to mount jerrycan on side step?
Here is another variation probably with a stand off of some kind...
Chuck Lutz
GPW 17963 4/24/42 Chester, PA. USA 20113473 (USA est./Tom W.)
Bantam T3-C 1947
GPW 17963 4/24/42 Chester, PA. USA 20113473 (USA est./Tom W.)
Bantam T3-C 1947
-
- G-Major General
- Posts: 3180
- Joined: Sat Jul 24, 2010 9:49 pm
- Location: Magnolia, Texas
- Contact:
Re: How to mount jerrycan on side step?
Are these brackets available from anywhere? Has anyone on the G fabricated them for sale? I would pay for one if I could find it. I think Chance is looking for one too.
- Chuck Lutz
- Gee Addict
- Posts: 26829
- Joined: Wed Jun 28, 2006 7:00 am
- Location: Jeep Heaven
Re: How to mount jerrycan on side step?
Just a suggestion; before you mount a pass side gas/water can on your jeep, trace the outline onto a piece of cardboard and duct tape it to the jeep after you approximate where your gas/water can will end up by holding one of them in place. Then let several of your family and friends who you intend to let ride with you see if they can negotiate the shrinking door opening area when they attempt to get into and especially OUT of the jeep. Any of them taller than 6' may have a problem with the smaller exit area.
Chuck Lutz
GPW 17963 4/24/42 Chester, PA. USA 20113473 (USA est./Tom W.)
Bantam T3-C 1947
GPW 17963 4/24/42 Chester, PA. USA 20113473 (USA est./Tom W.)
Bantam T3-C 1947
- John Neuenburg
- Gee Old Hand
- Posts: 3769
- Joined: Mon Mar 24, 2003 11:18 am
- Location: U.S. Left Coast
Re: How to mount jerrycan on side step?
Good thinking Stretch! You should know!Chuck Lutz wrote: ↑Tue Sep 05, 2017 7:59 amJust a suggestion; before you mount a pass side gas/water can on your jeep, trace the outline onto a piece of cardboard and duct tape it to the jeep after you approximate where your gas/water can will end up by holding one of them in place. Then let several of your family and friends who you intend to let ride with you see if they can negotiate the shrinking door opening area when they attempt to get into and especially OUT of the jeep. Any of them taller than 6' may have a problem with the smaller exit area.
The angled method makes more room for the leg. This or the vertical style requires a bracket, so no more work either way.
The kings of overloading jeeps were the British Special Air Service in the desert war. Up to 15 cans and two were mounted like this, based on every photo I have seen. Bracket sometimes an inch or two higher. Carol Mather (L) and Gordon Alston off to Tripoli
Military Vehicle Collectors of California
MVPA 7404
1942 Ford GPW British Special Air Service Regiment Replica
1944 Willys MB
1941 Indian 640
BSA Folding Bicycles
M1942 Command Post Tent
MVPA 7404
1942 Ford GPW British Special Air Service Regiment Replica
1944 Willys MB
1941 Indian 640
BSA Folding Bicycles
M1942 Command Post Tent
- Chuck Lutz
- Gee Addict
- Posts: 26829
- Joined: Wed Jun 28, 2006 7:00 am
- Location: Jeep Heaven
Re: How to mount jerrycan on side step?
The SAS gentlemen above had the luxury of basically being the aggressors in North Africa...meaning they set the trap or attacked German units on the run in their vehicles and did not dismount and dig foxholes as other units might be expected to do when on the offensive. While I would see no problem in mounting gas cans on the tub steps/fenders for that kind of warfare, I would not suggest it be used in combat in the ETO where you went looking for the Germans/Italians and may have to bail out of the jeep when you found them.
In addition, the SAS had to carry huge amounts of WATER in addition to FUEL in the desert which would not have been the same situation in Europe. The SAS was conducting hit-and-run activities which counted on catching the enemy unawares in many instances. In the ETO the Germans could practically see the allies advancing so the lack of surprise meant much more returned firepower.
Carrying 15 gallons of gas in the tank would generally last long enough until the supply tail caught up with an advancing unit or the attack stalled or the vehicle was destroyed...so carrying many additional jerrycans more than the additional 5 gallons the jeeps carried just made them burn easier if they ran into a blockade or enemy ambush.
So...for the owner who really wants to carry an extra five gallons of gas over and above the 15 in the tank and 5 his original jerrycans held, mounting it is certainly discretional at best but one that should be thought out if one wants to carry older Vets or if one's own family is "older". The doorways on the jeep are hard enough to get in/out of for them (and for me) so additional blocking in the doorway makes no sense.
However....if you MUST mount one on the pass side, why not take a page out of the off-roader's handbook and design a mount that can SWING AWAY out of the way to allow passengers easy access in/out of the vehicle?
In addition, the SAS had to carry huge amounts of WATER in addition to FUEL in the desert which would not have been the same situation in Europe. The SAS was conducting hit-and-run activities which counted on catching the enemy unawares in many instances. In the ETO the Germans could practically see the allies advancing so the lack of surprise meant much more returned firepower.
Carrying 15 gallons of gas in the tank would generally last long enough until the supply tail caught up with an advancing unit or the attack stalled or the vehicle was destroyed...so carrying many additional jerrycans more than the additional 5 gallons the jeeps carried just made them burn easier if they ran into a blockade or enemy ambush.
So...for the owner who really wants to carry an extra five gallons of gas over and above the 15 in the tank and 5 his original jerrycans held, mounting it is certainly discretional at best but one that should be thought out if one wants to carry older Vets or if one's own family is "older". The doorways on the jeep are hard enough to get in/out of for them (and for me) so additional blocking in the doorway makes no sense.
However....if you MUST mount one on the pass side, why not take a page out of the off-roader's handbook and design a mount that can SWING AWAY out of the way to allow passengers easy access in/out of the vehicle?
Chuck Lutz
GPW 17963 4/24/42 Chester, PA. USA 20113473 (USA est./Tom W.)
Bantam T3-C 1947
GPW 17963 4/24/42 Chester, PA. USA 20113473 (USA est./Tom W.)
Bantam T3-C 1947
- lightningdivision
- G-First Sergeant
- Posts: 133
- Joined: Tue Jan 03, 2006 6:44 am
- Location: Belgium
- Contact:
Re: How to mount jerrycan on side step?
I just used two pieces of wood,big enough so there was no problem with the window when it is up.
Very quick,easy and low cost.
Stijn
Very quick,easy and low cost.
Stijn
78th INFANTRY DIVISION
310th INFANTRY REGIMENT
Owner of "the bug mobile" '44 jeep
310th INFANTRY REGIMENT
Owner of "the bug mobile" '44 jeep
Who is online
Users browsing this forum: No registered users and 49 guests