I looking for a source for Correct Replacement Hub Studs used on the M3 37MM ATG. I don't have to have both "Right & Left" hand threads...all
"Right Hand" would be fine...But I would like for the inside Stud Flange to be correct. Has anyone here found a reliable source..??
Thanks Gents
Need source for Replacement M3 37MM ATG Wheel Hub Studs
- TiredIron
- G-Sergeant Major
- Posts: 199
- Joined: Wed May 28, 2003 12:53 pm
- Location:
Need source for Replacement M3 37MM ATG Wheel Hub Studs
"There is NO such thing as Overkill"
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: Need source for Replacement M3 37MM ATG Wheel Hub Studs
Are your hubs made for Jeep Wheels? Drive one out and post a pic. Measure the spline OD. I pic of the spline detail and the OD of the splines measured by a micrometer will confirm if they are MB/CJ-2A Jeep Studs. The 37MM AT Gun used two type wheels, the bolt patterns were different.
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
- TiredIron
- G-Sergeant Major
- Posts: 199
- Joined: Wed May 28, 2003 12:53 pm
- Location:
Re: Need source for Replacement M3 37MM ATG Wheel Hub Studs
Here's what I think I know so far. I haven't been able drive one of the studs out yet but I did get a lug nut off. I was told that they're not Jeep wheels but more than likely Studebaker wheels. By My measurements...the Studs are 1/2 inch diameter...1.0 inch long from the inside of flange....
and the flange up against the hub appears to be 15/16th diameter. I've Kroil'd the studs and will try beating on them again in a few days.
Thanks Gents
TiredIron
and the flange up against the hub appears to be 15/16th diameter. I've Kroil'd the studs and will try beating on them again in a few days.
Thanks Gents
TiredIron
"There is NO such thing as Overkill"
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: Need source for Replacement M3 37MM ATG Wheel Hub Studs
Put a nut flush with the end and use a 2# Hammer to give a stud a healthy whack, it will come out with no damage. That way you can post a pic of the stud and I can help you with exact replacements.
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
- TiredIron
- G-Sergeant Major
- Posts: 199
- Joined: Wed May 28, 2003 12:53 pm
- Location:
Re: Need source for Replacement M3 37MM ATG Wheel Hub Studs
PM sent back to you......
"There is NO such thing as Overkill"
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: Need source for Replacement M3 37MM ATG Wheel Hub Studs
Got it.
Will try to ID these using a couple other brands and see if they are still in stock locally.
Will try to ID these using a couple other brands and see if they are still in stock locally.
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
Who is online
Users browsing this forum: DDTrustee and 49 guests