Bantam wiring clip location?

Quarter-ton trailer series, Wanted, USED PARTS FOR SALE NO EBAY or COMMERCIAL SALES., and Knowledge Base
Post Reply
TonyStandefer
Sergeant Major of the Gee
Sergeant Major of the Gee
Posts: 474
Joined: Sun Apr 18, 2004 2:43 pm
Location: Everett, Wa

Bantam wiring clip location?

Post by TonyStandefer » Sat Feb 03, 2018 10:01 pm

Looking for a detailed pic of the clip that holds the vehicle cable to the top of the frame rail, thanks
Willys MB 340931. DOD 6-9-1944
Mvpa 1996 convention 1st place motorpool class
Dodge wc-12, July, 1941


User avatar
lowbonnet
G-Brigadier General
G-Brigadier General
Posts: 2173
Joined: Fri Dec 13, 2002 11:56 pm
Location: Holland

Re: Bantam wiring clip location?

Post by lowbonnet » Sat Feb 03, 2018 11:48 pm

This image shows the clip close to the trailer body on the top of the rail.

Image
June 1942 Ford GPW (script)
Transportation Equipment Co. T1, 1/4 ton trailer

Ben Hovis
G-Second Lieutenant
G-Second Lieutenant
Posts: 587
Joined: Fri Jul 16, 2004 4:27 pm
Location: Lincoln, California
Contact:

Re: Bantam wiring clip location?

Post by Ben Hovis » Fri Feb 09, 2018 5:53 pm

Tony,
Hope these pictures will assist your needs.
reassembly22.JPG
reassembly22.JPG (22.93 KiB) Viewed 717 times
reassembly32.JPG
reassembly32.JPG (20.73 KiB) Viewed 717 times
I believe this is correct.
Ben
http://www.jarheadjeep.com[url]
MB Body # 204065 date 1/19/43
GPW Engine # 12492 date 3/31/42
GPW Frame # 47894 date 7/?/42
Bantam T-3 1943 1/4 trailer USA # 0269414
http://www.jarheadjeep.com/Bens_1943_Ba ... railer[url]
PE 210 Power Unit Radio Generator 3/15/44

TonyStandefer
Sergeant Major of the Gee
Sergeant Major of the Gee
Posts: 474
Joined: Sun Apr 18, 2004 2:43 pm
Location: Everett, Wa

Re: Bantam wiring clip location?

Post by TonyStandefer » Sat Feb 10, 2018 4:29 pm

Perfect thanks!
Willys MB 340931. DOD 6-9-1944
Mvpa 1996 convention 1st place motorpool class
Dodge wc-12, July, 1941

User avatar
Chuck Lutz
Gee Addict
Posts: 26829
Joined: Wed Jun 28, 2006 7:00 am
Location: Jeep Heaven

Re: Bantam wiring clip location?

Post by Chuck Lutz » Thu Feb 15, 2018 8:56 am

Tony....interestingly enough, both the drawbars have the same part number...meaning they are interchangeable. So...if yours look to be a little dinged up, you can swap them from side to side to get the "best" top rail part where it can be seen....and of course that means the hole in the top of the drawbar for the clip screw was put into all drawbars in the same place so that no matter which side you installed them on...the hole would be in the correct location.

Here is my set up:
Front Wiring.jpg
Front Wiring.jpg (236.5 KiB) Viewed 646 times
Chuck Lutz

GPW 17963 4/24/42 Chester, PA. USA 20113473 (USA est./Tom W.)
Bantam T3-C 1947


Post Reply

Return to “Trailers 1/4 ton”

Who is online

Users browsing this forum: No registered users and 71 guests