I know this has come up before, did a search and could not find it...
I have a set of reproduction top bows, they do not come with the holes drilled in them for the rods to the windshield... I need the measurements from the pivot point to the holes...
Thanks...
Top Bow Measurements...
- kb1zq
- G-Major
- Posts: 950
- Joined: Sat Nov 08, 2003 9:26 pm
- Location: Del City, OK
Top Bow Measurements...
Hal, KB1ZQ
TSGT, USAF (Ret)
1952 M-38 CDN CAR 52-31313
1952 M-100 Strick #104
1951 Willys Wagon (In Restoration)
1954 Willys M38A1-201001205
Tornado Alley
Del City, OK
TSGT, USAF (Ret)
1952 M-38 CDN CAR 52-31313
1952 M-100 Strick #104
1951 Willys Wagon (In Restoration)
1954 Willys M38A1-201001205
Tornado Alley
Del City, OK
-
- G-Major
- Posts: 861
- Joined: Fri Dec 13, 2002 8:26 pm
- Location: LIVERMORE, CALIFORNIA
- kb1zq
- G-Major
- Posts: 950
- Joined: Sat Nov 08, 2003 9:26 pm
- Location: Del City, OK
-
- G-First Sergeant
- Posts: 131
- Joined: Mon Sep 01, 2008 4:49 am
- Location: Marine City, MI.
Re: Top Bow Measurements...
Reviving an old thread, I need to put these holes in my top bows. Is the 25 3/16 center to center ?
Thanks
Thanks
Curt W Kitter II
'42 MB (sold)
'51 M38
'52 M37 (sold)
'53 M211(sold)
'64 M105A1
'71 M151A2
'72 M35A2C
'72 M561 (sold)
MVPA # 17981
MVCC-MI
'42 MB (sold)
'51 M38
'52 M37 (sold)
'53 M211(sold)
'64 M105A1
'71 M151A2
'72 M35A2C
'72 M561 (sold)
MVPA # 17981
MVCC-MI
-
- G-First Lieutenant
- Posts: 646
- Joined: Sat Jun 02, 2012 1:21 pm
- Location: N.E. Ohio
Re: Top Bow Measurements...
I just went went out and measured. My bows are secured down and from that top pivot point all the way back to that small hole in the rail is indeed
25 3/16 center to center. John
25 3/16 center to center. John
-
- G-First Lieutenant
- Posts: 646
- Joined: Sat Jun 02, 2012 1:21 pm
- Location: N.E. Ohio
Re: Top Bow Measurements...
If you need a picture, I can send John
-
- G-First Sergeant
- Posts: 131
- Joined: Mon Sep 01, 2008 4:49 am
- Location: Marine City, MI.
Re: Top Bow Measurements...
Thank You.. John
Didn't want to put holes in the wrong place.
Didn't want to put holes in the wrong place.
Curt W Kitter II
'42 MB (sold)
'51 M38
'52 M37 (sold)
'53 M211(sold)
'64 M105A1
'71 M151A2
'72 M35A2C
'72 M561 (sold)
MVPA # 17981
MVCC-MI
'42 MB (sold)
'51 M38
'52 M37 (sold)
'53 M211(sold)
'64 M105A1
'71 M151A2
'72 M35A2C
'72 M561 (sold)
MVPA # 17981
MVCC-MI
Who is online
Users browsing this forum: No registered users and 49 guests